ESP32-S3 4inch Capacitive Touch Display Development Board
81.60 лв. (41.72 €) с вкл. ДДС
В наличност
Комплектът съдържа:
- ESP32 дисплей Waveshare ESP32-S3-Touch-LCD-4 – 1бр.
- Клема ъглова за I/O портовете – 1бр.
- Клема права за I/O портовете – 1бр.
Важно: В комплекта няма USB-C кабел!
Характеристики:
- Програмируем дисплей, работещ с ESP32-S3 микроконтролер
- Дисплей: 4inch IPS, 65K color, 480×480 pixels, 5-Point Capacitive Touch
- Микроконтролер: ESP32-S3-WROOM-1-N16R8 модул:
- 240 MHz Xtensa 32-Bit LX7 Dual-Core Processor, Integrated 512KB SRAM, 384KB ROM
- Flash: 16 MB
- PSRAM: 8 MB
- 2.4 GHz Wi-Fi (802.11 B/G/N)
- Supports Bluetooth 5 (LE) And Bluetooth Mesh
- On-board PCB antenna
- Захранване: с 5V от USB, или с 3,7V от Li-Po батерия или със 7-36V от захранващата клема
- Консумация при 5V: приблизително 250mA
- Зарядна верига за 3,7V Li-Po батерия с PH2.0 конектор
- I/O портове: USB, CAN, RS485, I2C
- RTC чип: PCF85063. Има зарядна верига и 1,27мм конектор за включване на 3V RTC акумулаторна бекъп батерия (Няма RTC батерия в комплекта)
- Програмира се през USB с Arduino IDE, с ESP32-IDF и др. Поддържа LVGL GUI programming
- Допълнителни: Micro SD card конектор, boot и reset бутони, пиезозумер (buzzer), ключета за вкл/изкл на 120 омовите резистори за CAN и RS485
- Размери: 84,2mm x 84,2mm
Допълнителна информация:
- ESP32-S3 4inch Capacitive Touch Display Development Board, 480×480, 5-Point Touch, 32-Bit LX7 Dual-Core Processor, Supports WiFi & Bluetooth, ESP32 With Display. Подробно описание
- ESP32-S3-Touch-LCD-4 Wiki. Документация, ръководство
DESCRIPTION EN:
ESP32-S3-Touch-LCD-4 is a microcontroller development board with 2.4GHz WiFi and BLE 5 support, integrates 16MB Flash and 8MB PSRAM. Onboard 4inch 480 × 480 capacitive touch screen can smoothly run GUI programs such as LVGL. Combined with various peripheral interfaces to quickly develop the HMI of ESP32-S3, suitable for scenarios such as smart control panel, home gateway, intelligent interactive panel, industrial control, and smart lighting control.
- Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
- Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
- Built in 512KB SRAM and 384KB ROM, with onboard 16MB Flash and 8MB PSRAM
- Onboard 4inch capacitive touch display, 480×480 resolution, 65K color
- Supports capacitive touch control via I2C interface, 5-point touch with interrupt support
- Onboard CAN, RS485, I2C interface and TF card slot, and integrates full-speed USB port
- Supports flexible clock, module power supply independent setting and other controls to realize low power consumption in different scenarios
Supports multiple peripherals
Supports the expansion of multiple peripherals via CAN, RS485, and I2C interfaces
Supports Two wiring methods
Comes with two types of screw terminals, allowing for bottom or back wiring, which is more convenient to integrate into various application scenarios such as DIN rail or embedded devices
What’s On Board
- ESP32-S3N16R8
The SoC with WiFi and Bluetooth, up to 240MHz operating frequency, integrated 8MB PSRAM and 16MB Flash - SW6106
Battery charging/discharging management chip - TJA1051T/3/1J
CAN transceiver - SP3485
RS485 transceiver - PCF85063
RTC chip - TCA9554PWR
IO expansion chip - XL1509-ADJE1 power chip
Supports 7~36V DC power input - 3.5mm 10pin screw terminal slot
for installing 3.5mm 10pin screw terminal block - RTC battery header
for connecting rechargeable RTC battery (only supports rechargeable RTC battery)
- USB Type-C port
ESP32-S3 USB interface, for power supply, burning program and printing logs - TF card slot
- PH2.0 Lithium battery header
PH2.0 2P connector, for 3.7V Lithium battery, supports charging and discharging - Buzzer
sound-producing peripheral - RS485 and CAN terminal resistor selection
close by defaul - Power supply indicator
- BOOT button
- RESET button
- BAT_PWR button
Power ON/OFF button when using battery for power supply
outline dimensions
Application Scenarios
Също може да ви хареса…
