ESP32-S3 7inch Capacitive Touch Display Development Board
93.00 лв. с вкл. ДДС
В наличност
Комплектът съдържа:
- ESP32 дисплей Waveshare ESP32-S3-Touch-LCD-7 – 1бр.
- Интерфейсен кабел HY2.0 2P to 2PIN male cable 10cm – 2бр.
- Интерфейсен кабел HY2.0 2P to 3PIN male cable 10cm – 1бр.
- Интерфейсен кабел HY2.0 2P to 4PIN male cable 10cm – 2бр.
Важно: В комплекта няма USB-C кабел!
Характеристики:
- Програмируем дисплей, работещ с ESP32-S3 микроконтролер
- Дисплей: 7inch, 65K RGB, 800×480 pixels, 5-Point Capacitive Touch
- Микроконтролер: ESP32-S3-WROOM-1-N8R8 модул:
- 240 MHz Xtensa 32-Bit LX7 Dual-Core Processor, Integrated 512KB SRAM, 384KB ROM
- Flash: 8 MB
- PSRAM: 8 MB
- 2.4 GHz Wi-Fi (802.11 B/G/N)
- Supports Bluetooth 5 (LE) And Bluetooth Mesh
- On-board PCB antenna
- Захранване: с 5V от USB или с 3,7V от Li-Po батерия.
- Консумация при 5V: приблизително 450-500mA
- Зарядна верига за 3,7V Li-Po батерия с PH2.0 конектор
- Работно напрежение GPIO портове: 3,3V
- I/O портове: USB, CAN, RS485, I2C, аналогов вход, UART/USB-UART, Micro SD card. (В комплекта има кабели за RS485, CAN, I2C и UART2 конекторите!)
- Програмира се през USB с Arduino IDE, с ESP32-IDF и др. Поддържа LVGL GUI interface demos
- Допълнителни: boot и reset бутони, ключ за избор на UART1 или UART2, джъмпери за вкл/изкл на 120 омовите резистори за CAN и RS485
- Размери: 192,96mm x 110,76mm
Допълнителна информация:
- Waveshare ESP32-S3 7inch Capacitive Touch Display Development Board, ESP32 With Display, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor, Supports WiFi & Bluetooth. Подробно описание
- ESP32-S3-Touch-LCD-7 Wiki. Документация, ръководство
DESCRIPTION EN:
ESP32-S3-Touch-LCD-7 is a microcontroller development board with 2.4GHz WiFi and BLE 5 support, integrates high-capacity Flash and PSRAM. Onboard 7inch capacitive touch screen can smoothly run GUI programs such as LVGL. Combined with various peripheral interfaces, suitable for the quick development of the HMI and other ESP32-S3 applications
- Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
- Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
- Built in 512KB of SRAM and 384KB ROM, with onboard 8MB PSRAM and 8MB Flash
- Onboard 7inch capacitive touch display, 800×480 resolution, 65K color
- Supports capacitive touch control via I2C interface, 5-point touch with interrupt support
- Onboard CAN, RS485, I2C interface and TF card slot, integrates full-speed USB port
- Supports flexible clock, module power supply independent setting, and other control to realize low power consumption in different scenarios
What’s On Board
- ESP32-S3N8R8
The SoC with WiFi and Bluetooth, up to 240MHz operating frequency, integrated 8MB PSRAM and Flash - 7inch display panel connector
- Touch panel connector
- TF card slot
- USB Type-C port
- UART1 Port
USB TO UART Type-C port - UART2 connector
UART1 and UART2 are the same UART, selected by switch - Sensor header
- CAN header
- I2C header
- RS485 header
- 3.7V single lithium battery PH2.0 header
- CAN terminal resistor selection
- RS485 terminal resistor selection
- UART selection
select UART1 or UART2 - BOOT button
Press and hold while powering on for program burning - RESET button
- I2C level selection
3.3V / 5V - DONE
Lithium battery charging completed indicator - CHG
Lithium battery charging indicator - PWR
Power supply indicator
Dimensions
Application Scenarios
Supports Multiple Peripherals
Supports The Expansion Of Multiple Peripherals Via Sensor, CAN, RS485, And I2C Interfaces
