Комплектът намира приложение при експериментиране и изграждане на прототипи с Raspberry Pi Pico микроконтролерни платки (няма Raspberry Pi Pico платка в комплекта). Модулите са опроводени през основната платка към съответните портове на разширителната платка за Raspberry Pi Pico. Ако бъдат отделени от основната платка, тогава е необходимо да се използват включените в комплекта кабели за да се свържат със съответните конектори на разширителната платка.
Важно: Няма Raspberry Pi Pico платка в комплекта, предлага се отделно – Raspberry Pi Pico платки.
Съдържание на комплекта:
- Комплект модули на основната платка:
- Разширителна платка, състояща се от: конектори за Raspberry Pi Pico; конектори за връзка с модулите чрез кабелите от комплекта; зарядно и конектор за Li-Po батерия (зарядното се захранва от Raspberry Pi Pico платката)
- Модул с 1.5inch OLED дисплей, SSD1327, 128х128, I2C, SPI
- Модул с IMU сензор QMI8658C (3-осови акселерометър и жироскоп)
- Модул със сензор за газ SGP40, VOC
- Модул с потенциометър
- Модул с фоторезистор (сензор за светлина)
- Модул с микрофон (сензор за звук)
- Модул с RGB светодиод, WS2812B
- Модул с пасивен пиезозумер (Buzzer)
- Модул с IR приемник IRM-H638T/TR2
- Модул с IR предавател TSAL6400
- Модул с бутон
- Модул със светодиод, 12мм, червен
- Модул със сензор за влажност и температура SHTC3
- Модул с AT24C04 EEPROM, 2Кbit, I2C
- Модул за управление на мотори, I2C, 2 х TB6612FNG
- Kабел PH2.0 dual-plug 4PIN – 15бр.
- Kабел PH2.0 4PIN plug to 2.54 female – 5бр.
- IR дистанционно управление – 1бр.
Допълнителна информация:
- Raspberry Pi Pico Entry-Level Sensor Kit, Including Pico Expansion Board and 15 common modules, All-in-one design. Подробно описание
- Raspberry-Pi-Pico-Sensor-Kit-B. Ръководство, примерен код, документация
- Схема
① Onboard PH2.0 header for 3.7V Lithium battery, allows recharging the battery and powering the board at the same time.
② Onboard PH2.0 4PIN headers for connecting modules
- Built in controller: SSD1327
- Resolution: 128×128
- 16 gray scale display
- I2C and SPI communication, switchable via onboard BS1 and BS2 resistors
- Onboard QMI8658C (3-axis accelerometer, 3-axis gyroscope), for detecting motion and orientation
- 16-bit resolution for both accelerometer and gyroscope
- Onboard SGP40 digital VOC gas sensor for air quality detection
- Measurement range: 0~1000ppm ethanol equivalents
- Communication interface: I2C (constant address: 0x59)
- Operating voltage: 3.3V/5V
Adjustable voltage output, after the output voltage exceeds the LED conduction voltage, the LED brightness will increase with voltage
For detecting the ambient light brightness, the output voltage will decrease as the brightness increases
For converting the sound signal into electrical signal, which is amplified through operational amplifier and then inputted to the comparator, providing analog voltage output and digital output respectively. Adjustable output amplitude via potentiometer A and digital interface trigger voltage via potentiometer D.
- Built in controller: WS2812B
- Brightness: 256 levels adjustable
- Color depth: 24 bits (R / G / B 8-bit each color, can be combined to 16777216 colors)
Onboard passive buzzer, outputs different sounds according to the different frequencies of the electrical signal.
Onboard IRM-H638T/TR2 for receiving infrared remote control signal
Onboard TSAL6400 for transmitting infrared remote control signals, with the infrared light wavelength of 940nm.
Onboard 12×12mm button, for human-computer interaction
Onboard 10mm LED with soft light, for status indication
Onboard SHTC3 chip supports measuring 0 to 100% relative humidity and -40°C to 125°C temperature, with a typical measurement accuracy of ±2% relative humidity and ±0.2°C
Onboard AT24C04 chip for preserving 2Kbit of data when powered down
- Onboard PCA9685 chip, can output 12-bit hardware PWM to control motor speed
- Onboard TB6612FNG dual H-bridge motor driver chip, high efficiency, not easy to heat
- logic voltage: 3.3V