Комплектът съдържа:
- R800C GSM/GPRS HAT – 1бр.
- GSM/GPRS aнтена – 1бр.
- Крепежни елементи
Характеристики:
- Проектиран е за монтаж върху Raspberry Pi, но е предвиден допълнителен конектор за контрол и връзка с други микроконтролерни платки – Arduino, Raspberry Pi Pico, ESP32 и др.
- Размери платка: 65mm x 30,5mm
- GSM Модул: QUAD-Band Simcom R800C GSM/GPRS
- Интерфейс: сериен – TTL UART
- Управлява се чрез АТ команди
- Конектор за слушалки и микрофон
- Захранване: 5V подавано от Raspberry Pi или на обозначените изводи на допълнителния интерфейсен конектор
- Максимална консумация: до 2А
- Работно напрежение: 3,3V или 5V – конфигурира се с джъмпер
- SMA конектор за антената (има антена в комплекта)
- Конектор за стандартен размер SIM карта
Допълнителна информация:
- Waveshare R800C GSM/GPRS HAT For Raspberry Pi. Сайт на производителя
- Wiki R800C GSM/GPRS HAT. Ръководство
- Resource. Докумнтация, AT команди, схема и др.
Features:
The R800C GSM/GPRS HAT is a handy, low power Raspberry Pi HAT which features multi-communication functionalities: GSM, GPRS, and phone call, applicable to countries or regions with 2G network coverage, up to 85.6kbps GPRS speed. It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, and so on.
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards and Jetson Nano
- Supports SMS, phone call, GPRS, TCP/IP, DTMF, HTTP, FTPl, etc.
- UART interface, for connecting controller boards like Arduino/STM32
- Onboard voltage translator, 3.3V by default, switch to 5V via jumper
- 2x LED indicators, easy to monitor the working status
- SIM card slot, supports 1.8V/3V SIM card
- Baudrate: 2400bps ~ 115200bps (115200bps by default)
- Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)
- Supports SIM application toolkit: GSM 11.14 Release 99
- Comes with online development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)
Specifications:
GSM / GPRS / AUDIO | |
---|---|
Frequency band | GSM: 850/900/1800/1900 MHz Quad-band auto search Compliant to GSM phase 2/2+ |
Emitting power | Class 4 (2W @ 900 MHz) Class 1 (1W @ 1800 MHz) |
GPRS connectivity | GPRS multi-slot class 12/10 (default) GPRS multi-slot class 1~12 (configurable) |
GPRS data feature | UL/DL speed: ≤85.6kbps Supports Packet Broadcast Control Channel (PBCCH) Coding schemes: CS-1, CS-2, CS-3, CS-4 Supports PAP (Password Authentication Protocol) for PPP connection Supports Unstructured Supplementary Service Data (USSD) |
SMS | Supports: MT, MO, CB, Text, PDU SMS storage: SIM card |
Audio | Voice encode/decode mode: Half Rate, Full Rate, Enhanced Full Rate, Adaptive Multi Rate Support echo cancellation Support noise reduction |
OTHERS | |
Power supply | 5V |
Logic level | 5V / 3.3V (default) |
Operating temperature | -40°C ~ 85°C |
Storage temperature | -45°C ~ 90°C |
Dimensions | 30.2 x 65mm |
What’s On Board
- R800C module
- RT9193-33 power chip
- MIC29302 power chip
- TXS0108EPWR voltage translator
translates 3.3V/5V into 1.8V - Raspberry Pi GPIO Header
for connecting with Raspberry Pi - Operating voltage selection jumper
VCC-3.3V: set operating voltage as 3.3V
VCC-5V: set operating voltage as 5V - PWR selection jumper
PWR-P4: startup/shutdown by the Raspberry Pi P4 pin - 3.5mm earphone/mic jack
- R800C control header
for easily connecting with host boards like STM32 - GSM Antenna Connector
- SIM Card slot
- R800C power on/off
Press for 1s to start up the R800C.
Press for 1s to shutdown the R800C after booting - NET Indicator
Fast flashing when module starts, flashing slowly after GSM register succeed - Power Indicator